Hollow Point Racing  


Instagram

-- WELCOME TO HOLLOW POINT RACING --    --
Go Back   Hollow Point Racing > The Garage > Member Builds

Reply
 
Thread Tools Display Modes
Old 04-10-2012, 08:38 AM   #1
Venom351R
95 R Inside
12 Second Club
 
Venom351R's Avatar
 
Join Date: Jan 2009
Location: Maine
Posts: 614
Default Venom351R's 351W, Rear end, Exhaust project

Been awhile since Ive posted on here, been awhile since driving the Mustang. Last time it actually ran was september of 2010. 2011 was not a good year, planned on getting it running again but money and time frame issues all became a factor so it sat with the engine mostly assembled. I'm now at the point where it should be running in May. I'll start from the beginning.

Came to the conclusion that my oil leaking issues from the intake were due to a intake bolt hole in the head that was stripped ( 2 of them ) The heads were AFR 185's with 72cc Combustion chambers, great for boost not so much for N/A. Made the decision to take the heads off and sell them.




Decided as well that I was going to get some parts powder coated since I had it all torn apart so I stripped down the Victor EFI 5.8 Intake





repainted the valve covers.





Intake powder coated, also had the accessory brackets done.








Oh yes there was a cylinder head upgrade in here as well. These are custom CNC Ported 234HR High Ports from Ed Curtis 64cc Combustion Chambers. Flow Numbers....

Lift Intake Exhaust
.100" 80 .58
.200" 142 115
.300" 196 150
.400" 258 190
.500" 304 215
.550" 320 220
.600" 333 222
.650" 340 230
.700" 334 236
.750" 340 238

And the cylinder heads....








__________________
1994 SVT Cobra #42 of 5009/ 95 Cobra R drivetrain

Performance- FTI Trickflow CNC 234HR High Ports/ Edelbrock Victor 5.8/FTI Camshaft/Acufab 75MM TB/ PMAS 95MM Velocity Meter/Tremec 3550

Chassis/Suspension- 6 Point Cage/Welded Subframes / Maximum Motorsport LCA/ Team Z UCA / Team Z K Member/ Team Z coilovers/ Strange 10 way Shocks & Struts

Exhaust- Magnaflow Catback/ Custom H Pipe/Accufab 1 3/4 Long Tubes

Misc- FMS 4.10/ Centerforce clutch/Moser 31 Spline axles/FMS 31 spline limited slip differential


Venom351R is offline   Reply With Quote
Old 04-10-2012, 08:39 AM   #2
Venom351R
95 R Inside
12 Second Club
 
Venom351R's Avatar
 
Join Date: Jan 2009
Location: Maine
Posts: 614
Default






Only one thing left to do after you get them of course PVC was also checked before bolting them down.




For the most part the engine was fully assembled. This is as far as I got by the end of the year in 2011. I had the long tubes but was not able to send them off to be coated.






Speaking of long tubes... Accufab 1 3/4 with 3" primary's





Early this spring I came to the conclusion that I should get the rear end rebuilt.



__________________
1994 SVT Cobra #42 of 5009/ 95 Cobra R drivetrain

Performance- FTI Trickflow CNC 234HR High Ports/ Edelbrock Victor 5.8/FTI Camshaft/Acufab 75MM TB/ PMAS 95MM Velocity Meter/Tremec 3550

Chassis/Suspension- 6 Point Cage/Welded Subframes / Maximum Motorsport LCA/ Team Z UCA / Team Z K Member/ Team Z coilovers/ Strange 10 way Shocks & Struts

Exhaust- Magnaflow Catback/ Custom H Pipe/Accufab 1 3/4 Long Tubes

Misc- FMS 4.10/ Centerforce clutch/Moser 31 Spline axles/FMS 31 spline limited slip differential


Venom351R is offline   Reply With Quote
Old 04-10-2012, 08:41 AM   #3
Venom351R
95 R Inside
12 Second Club
 
Venom351R's Avatar
 
Join Date: Jan 2009
Location: Maine
Posts: 614
Default

To go along with the rear end I decided to get a set of Team Z solid bushings and double adjustable upper control arms.




Got the rear end back from Ford and installed back in with the help of a friend.




Bought a Mac 3" prochamber to connect to the long tubes.







So as of now that brings this up to the current date. The long tubes have been sent off to be coated and I plan on buying a Borla cat back system next month. I have to buy an aftermarket steering shaft b/c of the long tubes, all the exhaust connections, oil, coolant, cats and that should pretty much do it. This started off as just replacing the cylinder heads but a lot of other things got done in the meantime. Should be all set sometime this may then I'll have to get it retuned and then finally I'll make it back to the track to hopefully click off some 11 second N/A runs. Where in the 11's I'm not sure Ive had responses all over the place about it. Before hand with the other cylinder heads my compression was 8:4 and it had 344 RWHP. With these heads I have 9:7 compression and the rear suspension upgrades should help it hook even more so needless to say it should be an exciting year as long as everything goes well as long as it its up and running next month
__________________
1994 SVT Cobra #42 of 5009/ 95 Cobra R drivetrain

Performance- FTI Trickflow CNC 234HR High Ports/ Edelbrock Victor 5.8/FTI Camshaft/Acufab 75MM TB/ PMAS 95MM Velocity Meter/Tremec 3550

Chassis/Suspension- 6 Point Cage/Welded Subframes / Maximum Motorsport LCA/ Team Z UCA / Team Z K Member/ Team Z coilovers/ Strange 10 way Shocks & Struts

Exhaust- Magnaflow Catback/ Custom H Pipe/Accufab 1 3/4 Long Tubes

Misc- FMS 4.10/ Centerforce clutch/Moser 31 Spline axles/FMS 31 spline limited slip differential



Last edited by Venom351R; 04-10-2012 at 08:47 AM.
Venom351R is offline   Reply With Quote
Old 04-10-2012, 10:02 AM   #4
mellis
Fackin destroying tires
 
mellis's Avatar
 
Join Date: Jul 2009
Location: Worcester, MA
Posts: 1,833
Default

Looks badass dude! Should be sweet when its done
__________________
2004 Torch Red GT
On3 Turbo upgrade in process...
mellis is offline   Reply With Quote
Old 04-10-2012, 10:31 AM   #5
TheCat033
The Green Monster
10 Second Club
 
TheCat033's Avatar
 
Join Date: Oct 2008
Location: Lunenburg, Ma
Posts: 7,063
Default

Glad you'll be back in the game finally, I know how it goes you upgrade on thing, then another, and another lol. Nice work all around
__________________

2001 DHG Mustang Bullitt #00293
______________________________

2001 Black Mustang Bullitt #05466
TheCat033 is offline   Reply With Quote
Old 04-10-2012, 10:51 AM   #6
candyroush
Senior Member
 
candyroush's Avatar
 
Join Date: Dec 2008
Location: Pepperell
Posts: 493
Default

Sweet build, those are some serious flow numbers!! I remember this car from FFW a few years ago.
__________________
candyroush is offline   Reply With Quote
Old 04-10-2012, 11:50 AM   #7
Venom351R
95 R Inside
12 Second Club
 
Venom351R's Avatar
 
Join Date: Jan 2009
Location: Maine
Posts: 614
Default

Thanks guys, and I plan on being back for Tasca day this year. Once I get this combo all squared away I'm thinking of doing some Nitrous down the road further if I want to make a run at some 10's. But thats after I get everything all squared away currently.

Forgot to mention the heads are 2.05 valves and 1.60 exhaust.
__________________
1994 SVT Cobra #42 of 5009/ 95 Cobra R drivetrain

Performance- FTI Trickflow CNC 234HR High Ports/ Edelbrock Victor 5.8/FTI Camshaft/Acufab 75MM TB/ PMAS 95MM Velocity Meter/Tremec 3550

Chassis/Suspension- 6 Point Cage/Welded Subframes / Maximum Motorsport LCA/ Team Z UCA / Team Z K Member/ Team Z coilovers/ Strange 10 way Shocks & Struts

Exhaust- Magnaflow Catback/ Custom H Pipe/Accufab 1 3/4 Long Tubes

Misc- FMS 4.10/ Centerforce clutch/Moser 31 Spline axles/FMS 31 spline limited slip differential



Last edited by Venom351R; 04-10-2012 at 11:52 AM.
Venom351R is offline   Reply With Quote
Old 04-10-2012, 03:57 PM   #8
Venom351R
95 R Inside
12 Second Club
 
Venom351R's Avatar
 
Join Date: Jan 2009
Location: Maine
Posts: 614
Default

well here is what I accomplished today and how it currently sits in the garage




I know your probably thinking, big deal you got the rear wheels on lol. Well its what finally putting on the rear wheels means. I'm done working on the rear end. I set the pinion angle this after noon and reconnected the drive shaft. So now I no longer have to get in and out from under the back side so the rear wheels could go back on and it finally looks mostly like a car again
__________________
1994 SVT Cobra #42 of 5009/ 95 Cobra R drivetrain

Performance- FTI Trickflow CNC 234HR High Ports/ Edelbrock Victor 5.8/FTI Camshaft/Acufab 75MM TB/ PMAS 95MM Velocity Meter/Tremec 3550

Chassis/Suspension- 6 Point Cage/Welded Subframes / Maximum Motorsport LCA/ Team Z UCA / Team Z K Member/ Team Z coilovers/ Strange 10 way Shocks & Struts

Exhaust- Magnaflow Catback/ Custom H Pipe/Accufab 1 3/4 Long Tubes

Misc- FMS 4.10/ Centerforce clutch/Moser 31 Spline axles/FMS 31 spline limited slip differential


Venom351R is offline   Reply With Quote
Old 04-21-2012, 07:53 PM   #9
Venom351R
95 R Inside
12 Second Club
 
Venom351R's Avatar
 
Join Date: Jan 2009
Location: Maine
Posts: 614
Default

Headers came back today after being ceramic coated.





__________________
1994 SVT Cobra #42 of 5009/ 95 Cobra R drivetrain

Performance- FTI Trickflow CNC 234HR High Ports/ Edelbrock Victor 5.8/FTI Camshaft/Acufab 75MM TB/ PMAS 95MM Velocity Meter/Tremec 3550

Chassis/Suspension- 6 Point Cage/Welded Subframes / Maximum Motorsport LCA/ Team Z UCA / Team Z K Member/ Team Z coilovers/ Strange 10 way Shocks & Struts

Exhaust- Magnaflow Catback/ Custom H Pipe/Accufab 1 3/4 Long Tubes

Misc- FMS 4.10/ Centerforce clutch/Moser 31 Spline axles/FMS 31 spline limited slip differential


Venom351R is offline   Reply With Quote
Old 04-21-2012, 11:45 PM   #10
mellis
Fackin destroying tires
 
mellis's Avatar
 
Join Date: Jul 2009
Location: Worcester, MA
Posts: 1,833
Default

That looks awesome, how much did that cost you?
__________________
2004 Torch Red GT
On3 Turbo upgrade in process...
mellis is offline   Reply With Quote
Old 04-22-2012, 06:37 AM   #11
Venom351R
95 R Inside
12 Second Club
 
Venom351R's Avatar
 
Join Date: Jan 2009
Location: Maine
Posts: 614
Default

They were $200 and $50 shipping each way. I had them sent to Joplin MO to a place called performance coatings on the reccomendation of a friend who had his headers coated by them
__________________
1994 SVT Cobra #42 of 5009/ 95 Cobra R drivetrain

Performance- FTI Trickflow CNC 234HR High Ports/ Edelbrock Victor 5.8/FTI Camshaft/Acufab 75MM TB/ PMAS 95MM Velocity Meter/Tremec 3550

Chassis/Suspension- 6 Point Cage/Welded Subframes / Maximum Motorsport LCA/ Team Z UCA / Team Z K Member/ Team Z coilovers/ Strange 10 way Shocks & Struts

Exhaust- Magnaflow Catback/ Custom H Pipe/Accufab 1 3/4 Long Tubes

Misc- FMS 4.10/ Centerforce clutch/Moser 31 Spline axles/FMS 31 spline limited slip differential


Venom351R is offline   Reply With Quote
Old 04-22-2012, 10:01 PM   #12
TheCat033
The Green Monster
10 Second Club
 
TheCat033's Avatar
 
Join Date: Oct 2008
Location: Lunenburg, Ma
Posts: 7,063
Default

Those look mint dude
__________________

2001 DHG Mustang Bullitt #00293
______________________________

2001 Black Mustang Bullitt #05466
TheCat033 is offline   Reply With Quote
Old 04-23-2012, 07:24 AM   #13
Venom351R
95 R Inside
12 Second Club
 
Venom351R's Avatar
 
Join Date: Jan 2009
Location: Maine
Posts: 614
Default

almost a shame that most of all that shineyness will be under the car and the rest only seen when the hood is open.
__________________
1994 SVT Cobra #42 of 5009/ 95 Cobra R drivetrain

Performance- FTI Trickflow CNC 234HR High Ports/ Edelbrock Victor 5.8/FTI Camshaft/Acufab 75MM TB/ PMAS 95MM Velocity Meter/Tremec 3550

Chassis/Suspension- 6 Point Cage/Welded Subframes / Maximum Motorsport LCA/ Team Z UCA / Team Z K Member/ Team Z coilovers/ Strange 10 way Shocks & Struts

Exhaust- Magnaflow Catback/ Custom H Pipe/Accufab 1 3/4 Long Tubes

Misc- FMS 4.10/ Centerforce clutch/Moser 31 Spline axles/FMS 31 spline limited slip differential


Venom351R is offline   Reply With Quote
Old 04-29-2012, 05:31 PM   #14
Venom351R
95 R Inside
12 Second Club
 
Venom351R's Avatar
 
Join Date: Jan 2009
Location: Maine
Posts: 614
Default

Finished off the rest of the engine today. Just have to get a PS Pump cap and waiting for the spark plugs to ship to me. Had to return the set I had and the others are on back order until the 11th of May. On the 16th I'll be ordering the Borla cat back system and that weekend I'll have a few extra hands to help with installing the long tubes and the rest of the exhaust system then I'll cross my fingers and hope it starts and runs.




__________________
1994 SVT Cobra #42 of 5009/ 95 Cobra R drivetrain

Performance- FTI Trickflow CNC 234HR High Ports/ Edelbrock Victor 5.8/FTI Camshaft/Acufab 75MM TB/ PMAS 95MM Velocity Meter/Tremec 3550

Chassis/Suspension- 6 Point Cage/Welded Subframes / Maximum Motorsport LCA/ Team Z UCA / Team Z K Member/ Team Z coilovers/ Strange 10 way Shocks & Struts

Exhaust- Magnaflow Catback/ Custom H Pipe/Accufab 1 3/4 Long Tubes

Misc- FMS 4.10/ Centerforce clutch/Moser 31 Spline axles/FMS 31 spline limited slip differential


Venom351R is offline   Reply With Quote
Old 04-29-2012, 07:31 PM   #15
mellis
Fackin destroying tires
 
mellis's Avatar
 
Join Date: Jul 2009
Location: Worcester, MA
Posts: 1,833
Default

Just ordered some plugs for mine too. What did you go with? I got some Autolite 25's. Seemed to have great reviews, and i didnt wanna go any steps colder since im N/A. Well see how well they work haha
__________________
2004 Torch Red GT
On3 Turbo upgrade in process...
mellis is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump

All times are GMT -5. The time now is 05:37 AM.

Official PayPal Seal

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.